One of a kind ttr 90 build thread.....UPDATE NEW GRAFFIX KIT
Just started building up the ttr 90 with the part's that i've been collecting this past few week's.The fork's are KX 65 35mm shiver's with a rm 65 front wheel's and rm 65 front brake set up,the seat is a gut's racing one and the swing arm is a +5 down components klx 110/crf 70 one and the rear wheel is a xr 70 wheel but this will be changed for a reeg mx rear disc wheel or a faster mini rear disc wheel or a kx 65 rear wheel and i'll be using a reeg mx cable operated rear brake set up or a kx 65 rear brake set up.
This is just mocked up to lookin all the little custom bit's i need to make for it to all fit together so is no way near the finished bike but so far it's looking really good....The seat height is 32" from middle of seat to floor and the height from the rear spindle to back mud gaurd is 21" and the front fork travel is 8 and a half inch's the same as my reeg mx crf 70 bike.. theseat height to the peg's is roughly 19 inch's and the handle bar height will be the same as my crf 70 reeg mx bike....
So far i got to make to shim's for the swingarm and a new spacer for the rear wheel so the chain will be true and straight but i havent got a rear shock yet but i will get an 110 elka rear shock or a crf 70 one with remote res then i will know how much i need to move the rear shock mount on the frame...
There has'nt been no real problem's except what bottom bearing i need to use on the KX 65 steering tube as the stock ttr 90 one fit's straight on the top of the steering tube and the stock ttr 90 castel nut fit's the kx 65 steering tube aswell but the ttr 90 bearing's dont fit on the bottom of the KX 65 steering tube so what i might have to do is make a new custom bearing race for the bootom and use a ttr 90 top bearing on the bottom aswell,unless there's one out there that will fit from another bike...
The engine shoud be built up next week using a takegawa hyper s stage big bore kit with a two brother's race pipe and a new set of plastic's and graffix's in a few week's....finger's crossed....
If any one can give me help and advice on what steering tube bearing's i need then please let me know and also any other advice i might need to finish this build off....thank's BUZZ
Just started building up the ttr 90 with the part's that i've been collecting this past few week's.The fork's are KX 65 35mm shiver's with a rm 65 front wheel's and rm 65 front brake set up,the seat is a gut's racing one and the swing arm is a +5 down components klx 110/crf 70 one and the rear wheel is a xr 70 wheel but this will be changed for a reeg mx rear disc wheel or a faster mini rear disc wheel or a kx 65 rear wheel and i'll be using a reeg mx cable operated rear brake set up or a kx 65 rear brake set up.
This is just mocked up to lookin all the little custom bit's i need to make for it to all fit together so is no way near the finished bike but so far it's looking really good....The seat height is 32" from middle of seat to floor and the height from the rear spindle to back mud gaurd is 21" and the front fork travel is 8 and a half inch's the same as my reeg mx crf 70 bike.. theseat height to the peg's is roughly 19 inch's and the handle bar height will be the same as my crf 70 reeg mx bike....
So far i got to make to shim's for the swingarm and a new spacer for the rear wheel so the chain will be true and straight but i havent got a rear shock yet but i will get an 110 elka rear shock or a crf 70 one with remote res then i will know how much i need to move the rear shock mount on the frame...
There has'nt been no real problem's except what bottom bearing i need to use on the KX 65 steering tube as the stock ttr 90 one fit's straight on the top of the steering tube and the stock ttr 90 castel nut fit's the kx 65 steering tube aswell but the ttr 90 bearing's dont fit on the bottom of the KX 65 steering tube so what i might have to do is make a new custom bearing race for the bootom and use a ttr 90 top bearing on the bottom aswell,unless there's one out there that will fit from another bike...
The engine shoud be built up next week using a takegawa hyper s stage big bore kit with a two brother's race pipe and a new set of plastic's and graffix's in a few week's....finger's crossed....
If any one can give me help and advice on what steering tube bearing's i need then please let me know and also any other advice i might need to finish this build off....thank's BUZZ