PlanetMinis Forums banner
161 - 180 of 197 Posts

· Vendor
Joined
·
10,894 Posts
Discussion Starter · #161 ·
If you read it, the top one is a crf70 built motor. Seems that a crf70 is a legit Honda to me?
Thanks man We have built quite a few KLX and Honda motors
Geezer built that 114cc Honda motor
Thing was mint

So what constitutes a works motor? I have a Z155HO with the 184 kit and the V2 head and a YX 57mm crank. Is this considered a works motor? Full specs listed in my sig. If it is considerd a works motor what would it be worth with just over 2 hours on it.
We at T Bolt USA have been using the term "Works" to refer to motors WE build up , rebuild or otherwise work on to obtain high performance
"Works" was a term use to describe pre 1985 Factory MX Race bikes , We adopted it and its stuck
 

· Vendor
Joined
·
10,894 Posts
Discussion Starter · #168 ·
Check out this Geezer Build
Link:
Works Pitster Pro 125 RS OutLaw - Engines - Works Engines - WHS-1409 - TBolt USA, LLC
[h=1]Works Pitster Pro 125 RS OutLaw
[WHS-1409][/h]



RACE BUILT - READY TO RIP
CAT 5 Porting , Head work
TB V2 Roller Rocker Race Head
Titanium retainers

57 mm high compression piston

Special works 54mm cylinder

Complete ignition system
DEF the Fastest "125cc" around
Standard features:

4 up shifting

Type :4-Stroke single-cylinder OHC air cooled

Bore & Stroke: 54 x 57mm Bore (Outlaw)

Rear Clutch: manual clutch
Quick Access External Oil Filter
Quick Access Clutch

Gears: 4 speed

Magneto: Permanent magnetic

Voltage: 12 Volt

Engine will run accessories:

side cover, intake tube, shift lever, kick start lever


Add to Cart
 

· Registered
Joined
·
2,424 Posts
I had built this RS motor for myself. I guarantee this sucker is very fast. It specs out to 138 cc. It has a custom cam cover but the TB cam cover comes with it. The Connecting rod says made in Japan. I just have too much going on and it needs to be sold. Thanks for looking. Pm me if there are any questions. It's for sale on TBolt web sight under works motors
 

· Vendor
Joined
·
10,894 Posts
Discussion Starter · #170 ·
I had built this RS motor for myself. I guarantee this sucker is very fast. It specs out to 138 cc. It has a custom cam cover but the TB cam cover comes with it. The Connecting rod says made in Japan. I just have too much going on and it needs to be sold. Thanks for looking. Pm me if there are any questions. It's for sale on TBolt web sight under works motors
Here is a similar 124cc build in an English Speedway machine !

Land vehicle Vehicle Spoke Motorcycle Motorcycle speedway


Vehicle Engine Auto part Automotive engine part Motorcycle


Vehicle Engine Auto part Fuel line Car
 

· Vendor
Joined
·
10,894 Posts
Discussion Starter · #172 ·
[h=1]REVIEW OF GEEZER BUILD:

Honda 114cc Works Build
[TRC-0518][/h]

Date Added: Friday 26 April, 2013[h=2]by Clay K.[/h]
Seriously impressed, well built works awesome with a vm26 kit. Power wise it flat out rips and with a good exhaust has a sweet deep high compression sound. Night and day difference between this and stock. Good job fellas!


 

· Vendor
Joined
·
10,894 Posts
Discussion Starter · #173 ·
[h=1]Daytona Anima 190cc FDX Engine
[WHS-9107][/h]




The DAYTONA 190-FDX!

This 4 valve, 62mm bore x 62 mm stroke engine is the newest edition directly from Daytona Motor Co. The new FDX-190 comes stock with an updated close ratio transmission, an AUTO-DECOMPRESSION CAMSHAFT and reinforced crankcases.
The FDX motor is manufactured and assembled as a 190 at the Daytona factory.

Includes:
(1) Daytona FDX 190 engine
(1) Intake manifold
(1) Wire Harness
(1) CDI: ( 4 selectable timing settings & 5 selectable Rev Limiter setting)
(1) Ignition Coil
(1) Intake manifold carb boot

*Daytona crate engines do not come with any warranty*

 

· Vendor
Joined
·
10,894 Posts
Discussion Starter · #175 ·
Do you know when you might get more Lifan 125cc semi-auto motors in?
We have 125cc 1dn 3up manual $299
You got the last 4up semi !
Will have more 90cc / 125cc Lifam 4up semi & Manual this week hopefully

PLENTY of Piranha 90cc 125cc 140cc 150cc 160cc
Lots of Pitster Pro 90cc 110cc 125cc RS 140cc 155ccHO motors
Lets ride !
 

· Vendor
Joined
·
10,894 Posts
Discussion Starter · #177 ·
check out this geezer build
link:
works pitster pro 125 rs outlaw - engines - works engines - whs-1409 - tbolt usa, llc
works pitster pro 125 rs outlaw
[whs-1409]


race built - ready to rip
cat 5 porting , head work
tb v2 roller rocker race head
titanium retainers

57 mm high compression piston

special works 54mm cylinder

complete ignition system
def the fastest "125cc" around
standard features:

4 up shifting

type :4-stroke single-cylinder ohc air cooled

bore & stroke: 54 x 57mm bore (outlaw)

rear clutch: Manual clutch
quick access external oil filter
quick access clutch

gears: 4 speed

magneto: Permanent magnetic

voltage: 12 volt

engine will run accessories:

Side cover, intake tube, shift lever, kick start lever
we put this on aug special $749
 

· Vendor
Joined
·
10,894 Posts
Discussion Starter · #180 ·
161 - 180 of 197 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top