Planet Minis

jjpluml · 09-02-2008, 08:33 AM

ok so my little bro broke his throttle cable on his orion and i got a new one and slapped it on and now his bikes acting up hardcore. The bike will start and run with the choke on but when you turn the choke off it backfires through the carb and pops and then eventuallt dies. The bikes also smoking white in a bad way!!! tried adjusting the needle up to the middle clip but not any better. The plug is soaking wet when i pull it out also so i dunno wtf... HELP!!

onlydirt · 09-02-2008, 08:47 AM

Tare down the carb, clean it out, make sure the float isnt sticking. Makes sure the throttle cable is long enough, so its not pulling the carb open at all. Re set your idel screw.

jjpluml · 09-02-2008, 09:02 AM

where should the idle screw be setting? I mdae sure that the needle was closing all the way, u think the float could do this?

lemmonbomb · 09-02-2008, 09:24 AM

make sure the carb is clean and that the throttle cable has enough travel.

onlydirt · 09-02-2008, 10:03 AM

I had a bad float on an OKO and it did as you described.

jjpluml · 09-02-2008, 10:09 AM

the needle defanitly sets all the way down n the carb. No question. ive just never heard of a float makin a bike run like this

09-02-2008, 08:33 AM	#1 (permalink)
jjpluml PM Newbie Join Date: Aug 2008 Location: SPRINGDALE ARKANSAS Posts: 44	Carb problems ok so my little bro broke his throttle cable on his orion and i got a new one and slapped it on and now his bikes acting up hardcore. The bike will start and run with the choke on but when you turn the choke off it backfires through the carb and pops and then eventuallt dies. The bikes also smoking white in a bad way!!! tried adjusting the needle up to the middle clip but not any better. The plug is soaking wet when i pull it out also so i dunno wtf... HELP!!

09-02-2008, 08:47 AM	#2 (permalink)
onlydirt 2nd Gear Member Join Date: Sep 2007 Location: Kokomo,IN Posts: 657	Re: Carb problems Tare down the carb, clean it out, make sure the float isnt sticking. Makes sure the throttle cable is long enough, so its not pulling the carb open at all. Re set your idel screw.

09-02-2008, 09:02 AM	#3 (permalink)
jjpluml PM Newbie Join Date: Aug 2008 Location: SPRINGDALE ARKANSAS Posts: 44	Re: Carb problems where should the idle screw be setting? I mdae sure that the needle was closing all the way, u think the float could do this?

09-02-2008, 09:24 AM	#4 (permalink)
lemmonbomb 1st Gear Member Join Date: Jan 2007 Posts: 100	Re: Carb problems make sure the carb is clean and that the throttle cable has enough travel.

09-02-2008, 10:03 AM	#5 (permalink)
onlydirt 2nd Gear Member Join Date: Sep 2007 Location: Kokomo,IN Posts: 657	Re: Carb problems I had a bad float on an OKO and it did as you described.

09-02-2008, 10:09 AM	#6 (permalink)
jjpluml PM Newbie Join Date: Aug 2008 Location: SPRINGDALE ARKANSAS Posts: 44	Re: Carb problems the needle defanitly sets all the way down n the carb. No question. ive just never heard of a float makin a bike run like this

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)